Tensioned Cable Hardware

• Connection Hardware - Hardware used to connect the cable to the corner hardware, turnbuckles and the netting mesh.
• Corner Hardware - Maximum strength hardware used at all corners, cable stops and at both ends of support cables.
• Cable Guides - Hardware used to prevent gaps between the cable and the installation surface.

Net Cable
HD Stainless Steel aircraft cable, 7x7, 3/32” (2mm) diameter with 920 lb. tensile stength. Available in 250' and 500' spools.

Net Cable G
HD Galvanized aircraft cable, 7x7, 3/32" (2mm) diameter with 920 lb. tensile strength. Available in 250' and 500' spools.

Wire Rope Thimbles
HD forged steel connection thimbles prevent cable kinks and frays. Available in Stainless and galvanized steel.

Wire Rope Clamps
Required loop connection hardware for cable runs of 25’ or more. Minimum of 2 rope clamps per cable connection.

Ferrules
For connecting short cable runs (less than 25’). Zinc plated copper. Ratchet Crimper required. 2 ferrules per cable connection. IN STOCK

Large Eyebolt w/Nut
HD stainless steel eyebolt, 9/16” I.D., 1” stem, 1/4-20 thread with stainless hex-nut. For steel or masonry surfaces – masonry anchors sold separately. IN STOCK

Eyebolt 2 w/Nut
HD stainless steel eyebolt, 9/16” I.D., 2” stem, 1/4-20 thread with stainless hex-nut.  Use only for surfaces to thick to use the 1" eyebolts. IN STOCK

Machine Screw Anchors
HD expansion anchors for eyebolts. ¼-20 thread for large eyebolt and 10-24 thread for small eyebolt. Steel setting tools purchased separately.

Large Screw Eye
HD stainless steel screw eye, 17/32” I.D., 1” lag thread. For wood or thick sheet metal surfaces (pre-drill recommended for sheet metal). IN STOCK

Zinc Plated Eye Bolt with Shield Anchor
HD Zinc Plated expansion eyebolt used for corner hardware on runs 100 ft or less. Use 12mm drill bit to install. OUT OF STOCK

Turnbuckles
HD stainless steel or galvanized hook & eye turnbuckles for tensioning Net Cable.

Small Eyebolt w/Nut
All stainless 9/32” I.D., 3/4” stem, 10-24 nut. For steel or masonry surfaces – masonry anchors sold separately. IN STOCK

Small Screw Eye
Screw eye stainless steel 7/32” I.D., 11/16” lag thread. For wood or sheet metal surfaces (pre-drill required for sheet metal surface). IN STOCK

Sidewinders for steel
HD self-drill, self-tap cable guides for steel. Use SWD-2.0 for steel up to 1/4” thick. Use #SWDR-1.5 for steel up to 1/2” thick. Sidewinder Driver Socket required.

Sidewinders for concrete
HD self-threading cable guides for masonry surfaces. Requires a ¼” diameter hole. Sidewinder Driver Socket required.

Sidewinder Driver Socket
HD socket driver required for all Sidewinder cable guides. IN STOCK

Stainless lag threaded eyelet cable guide
Stainless steel lag threaded eyelet cable guide. Screws into wood, plastic, composite, etc. OUT OF STOCK

Galvanized Net Spike
HD Gavlanized Net Spike cable guide for solid concrete and stone. IN STOCK

Black Oxide Flange Clips
Black oxide coated spring steel hammer on flange clips. No-drill hammer-on flange clips used as Cable Guides. 3 sizes to choose from.

Stainless Steel Flange Clips
All stainless steel hammer on flange clips. No-drill hammer-on girder clips used as Cable Guides. 3 sizes to choose from.

E-Z Clip
Stainless steel sheet metal form that can be fastened to all types of surface materials.  1 1/4" x 1" x 1/4" with a 3/16" mounting hole. IN STOCK

Angle bracket cable guide
Stainless steel or Galvanized HD angle bracket has 2 - 1/4" dia. holes. One for mounting, one for the cable.

Stainless "J" Bracket cable guide
Stainless J Brackets are used as Cable Guides on all types of installation surfaces. IN STOCK

Stainless HD cable guide clamp
HD stainless steel toothed C-clamp firmly grips surfaces up to 3/4" thick. Cable runs on inside of C-clamp. OUT OF STOCK

Stainless Outside Corner Bracket
Stainless steel bracket with welded ring at outside corner. Use as a cable guide for any outside corners along short run cable installations. IN STOCK